代写program编程、代做c/c++，Python程序

项目预算：开发周期：发布时间：要求地区：

Previously, we set up a single router that connects two networks, so no rou7ng policy needs to be conﬁgured.
In this lab, you will ﬁrst need to learn from the next sec7on, “Router CLI terminal”, how to set up
sta7c/dynamic rou7ng policies.

Router CLI Terminal
The followings are brief explana7ons of some commonly used commands for seGng up routers:
Switching Diﬀerent Modes
Default status, in “User EXEC”: can only see some aspects of router
Router>

Using the command “enable” brings the user to “Privilege EXEC”: can see all conﬁgura7on of router
Router>enable

Router#

Using the command “conﬁgure terminal” brings the user to “Conﬁgure Mode”: Can make changes to the
conﬁgura7on. Type “exit” to quit.
Router# configure terminal

Router(config)#

Router(config)# exit

The Show Command
Before doing any ac7ons, it helps you checking the current conﬁgura7on informa7on on the router. It also
shows you a list of commands that you can use.
When you setup your network topology, try the followings:

Router# show ?

Router# show interfaces

Router# show ip interface brief

Router# show ip interface FastEthernet 0/1

2
The Interface Command
To review what you have conﬁgured, such as IP address for a speciﬁc router interface, in “Conﬁgure Mode”,
specify the “interface-name interface-number(slot/port)”

Router(config)# interface FastEthernet 0/1

Router(config-if)# ip address 192.168.1.5 255.255.255.0

Router(config-if)# no shutdown

Router(config-if)# exit
AVer seGng up its corresponding IP address and subnet mask, don’t forget to make it work by typing “no
shutdown”. Then “exit”, to use “show” command for this interface to check if the previous seGng is
successful.

Add/Remove sta?c routes

Sta7c routes tell a router where to send packets for a network that this router does not connect directly. In
this case, the router will forward this packet to an interface of one of the routers that this router directly
connects to.

Checking the exis7ng rou7ng table:

Router# show ip route

Then add a route, e.g.: any packets intend to go to the network “192.168.2.0 / 255.255.255.0”, will be
forwarded to the next hop router interface “192.168.3.1”:
Router(config)# ip route 192.168.2.0 255.255.255.0 192.168.3.1

If you want to remove this sta7c rou7ng policy, just use “no” format:

Router(config)# no ip route 192.168.2.0 255.255.255.0 192.168.3.1

Add a Dynamic Rou?ng Protocol – OSPF

Router(config)# router ospf 1
Router(config-router)# network 192.168.0.0 0.0.255.255 area 1
The “1” in both “router ospf 1” and “area 1” are not important for our lab, so leave it same as “1”
everywhere.“network 192.168.0.0 0.0.255.255”: means any of this router’s next hop router interface
begins with “192.168” will be conﬁgured with OSPF protocol. “0.0.255.255”: is a wildcard mask. It is NOT a
subnet mask. 3

Assignment # 2 Packet tracer (15%)
Network Topology for Beijing General Hospital

Q1. Create a network topology for Beijing General Hospital considering the main components to support the
following:

- Hospital Loca7on

- The Main Building: Administra7ve and Medical Staﬀ Oﬃces on this building. The remaining buildings house
various departments and medical facili7es. Hospital administra7ve staﬀ PCs are distributed throughout these
oﬃces and departments, and they share some networking equipment.

- Add three departments to the network topology:
- Department of Cardiology
- Department of Radiology
- Department of Neurology

- IT Department: The IT department hosts , the hospital's web server, pa7ent record server, and other servers.
There is also an email server hosted externally in the cloud.

- Staﬀ accommoda7ons Building

- Each department is expected to be on its own separate IP network.

- The switches should be conﬁgured with appropriate LANs.

- OSPF will be used to provide rou7ng for the routers in the internal network and sta7c rou7ng for the external
server.

- The devices in the Department of Cardiology will be expected to acquire dynamic IP addresses from a routerbased
DHCP server.

- The IP address for all subnets should begin with your UCD student number as hospital’s iden7ﬁer number.
For example, if the number is 192 022 02, then it should be 192.22.2.x. Use at least (could be longer) 25 bits
as your network preﬁx.

- You can es@mate the number of IP addresses in any network, but it should be a reasonable number.
Q2. How many subnets are in the network topology you build?

Q3. Show how you calculate the CIDR IP for each subnet.

Q4. List your IP, subnet mask, and gateway setup for all PCs and router interfaces.

Q5. Show an example of a sta7c route in your network; for example, if PC1 needs to connect to PC2, the
route should be: PC1 -> Router1 -> Router3 -> Router2 -> PC2
Then:
1. List in a table the key commands used in each router.
2. AVer this setup, provide a screenshot of the rou7ng table on each router.
3. When you can successfully PING PC0 -> PC2, show how you can trace its realis7c route that is correctly set.
4. Setup OSPF on each router; you should remove the previously conﬁgured sta7c route on each router.
5. Explain how OSPF is diﬀerent from the sta7c route regarding link state changes.

Submission:

1. .pkt ﬁle for the network topology (Logical and physical)
2. **PDF report** with answers for the “Ques7ons” suppor@ng all your answers with screenshots.
3. **Short video** (40 seconds) to explain your network topology.
Submission Deadline:
You should submit your assignment by Sunday, 09 June 2024